The Simos 3.3 system manages fuel injection, ignition, and electronic throttle actuation (EPC) in a single unit.
1 — GND (chassis ground) — ECU ground 2 — CAN High (CAN H) — Powertrain CAN bus high 3 — CAN Low (CAN L) — Powertrain CAN bus low 4 — Battery + (B+) — Permanent battery supply (fused) 5 — Ignition 15 (IGN) — Switched ignition supply 6 — 5V reference — Sensor supply reference 7 — MAP / Boost sensor input — Manifold absolute pressure 8 — IAT / Air temp sensor input — Intake air temperature 9 — CLT / Coolant temp sensor input — Engine coolant temperature 10 — Crankshaft position (CKP) — Primary crank sensor input 11 — Camshaft position (CMP) — Cam sensor input 12 — Knock sensor 1 — Knock input (engine bank-dependent) 13 — Knock sensor 2 — Secondary knock input (if fitted) 14 — Fuel injector 1 driver — Low-side injector driver (cylinder 1) 15 — Fuel injector 2 driver — Low-side injector driver (cylinder 2) 16 — Fuel injector 3 driver — Low-side injector driver (cylinder 3) 17 — Fuel injector 4 driver — Low-side injector driver (cylinder 4) 18 — Fuel pump control (FP relay driver) — Fuel pump relay control (switched output) 19 — Ignition coil driver 1 — Coil driver (or coil pack control) 20 — Ignition coil driver 2 — Coil driver 21 — Ignition coil driver 3 — Coil driver 22 — Ignition coil driver 4 — Coil driver 23 — TPS / Throttle position sensor — Throttle potentiometer input 24 — EGR valve control / N75 — EGR or turbo bypass control (model dependent) 25 — Idle control valve (IAC) — Idle air control / stepper or PWM 26 — Lambda sensor (oxygen) heater control — O2 sensor heater output 27 — Lambda sensor signal (upstream) — O2 sensor voltage input (bank 1) 28 — Secondary lambda / downstream signal — (if fitted) 29 — CAN GND / Chassis reference for CAN — optional/variant 30 — Vehicle speed / VSS — Speedometer/ABS speed signal input 31 — Brake switch input — Brake pedal / cruise inhibit 32 — Clutch switch input — Clutch pedal / cruise inhibit 33 — Neutral / Park switch — Gear selection input (if applicable) 34 — A/C request input — Air conditioning compressor request 35 — Fan control output 1 — Radiator fan relay control 36 — Fan control output 2 — Radiator fan stage 2 37 — Evaporative purge valve control — EVAP canister purge 38 — Ambient air temp input — Ambient temp sensor (if used) 39 — Accelerator pedal position sensor 1 — APS sensor 1 40 — Accelerator pedal position sensor 2 — APS sensor 2 (redundant) 41 — Start inhibit / starter motor input — Cranking detection input 42 — Immobilizer / PATS input — Immobilizer transponder data line 43 — Serial data / K-line (diagnostic) — Older K-line diagnostic port 44 — LIN bus / secondary serial — Variant-dependent 45 — CAN 2 High / FlexRay (variant) — Secondary bus high (if present) 46 — CAN 2 Low / FlexRay (variant) — Secondary bus low (if present) 47 — Alternator sense / L-terminal — Charge warning / alternator field sense 48 — Fuel rail pressure sensor — Fuel pressure sensor input (if fitted) 49 — Turbocharger control (VNT / boost) — Boost control solenoid driver 50 — Secondary injector drivers / spare outputs — Variant-dependent 51 — Knock ground / sensor ground — Dedicated sensor ground 52 — Switched supply for sensors (IGN2) — Secondary switched supply 53 — Ground (battery negative) — Main ground return 54 — Reserved / manufacturer test pin — DO NOT CONNECT 55 — Reserved / manufacturer test pin — DO NOT CONNECT simos 33a pinout top
is designated for the signal from the second petrol injector. Sensor Inputs G28 Engine Speed Sender : Crucial for determining RPM and ignition timing. Knock Sensors The Simos 3
These ECUs are often sent for professional repair to address common issues with horsepower loss, irregular idle speeds, or ignition timing failures. For advanced tuning or cloning, specialized tools like Knock Sensors These ECUs are often sent for
The Simos 33A pinout is a configuration used in some diesel engines, particularly in the automotive industry. I'll provide a detailed review of the Simos 33A pinout, focusing on the top aspects.